Search Results

A fan duct suitable for use with E3D V6 or Lite6 HotEnds. Injection moulded out of translucent polycarbonate. These are much harder wearing than printed parts and significantly less prone to vibration. These fan ducts are included as standard with all V6 (blue) and Lite6 (red) HotEnd kits.

This pack is the pinnacle of nozzle prowess, featuring six of E3D's most exciting, useful and experimental nozzles. Brass, Plated Copper Alloy, and Hardened Steel all feature in this kit, matched with the sizes we recommend for the most interesting use cases. Not to mention, this pack means you get...

High-performance brass nozzles for your Volcano HotEnd. From super-fine to super-fat layering, you'll be making stronger, faster and bigger prints in no time with the Volcano HotEnd PowerUp! These nozzles are immediately compatible with the LulzBot Moarstruder, but many RepRap 3D printers can be upgraded with an E3D Volcano. E3D...

Looking for a direct drive upgrade for your 3D printer? Titan Aero is a compact direct drive HotEnd and extruder combination. It takes the lightweight performance, reliability and usability of the V6 and Titan creating a more compact and refined unit. Compact & Rigid By combining the V6 and Titan into a single unit,...

Titanium V6 HeatBreaks are the perfect upgrade for printing at higher temperatures, helping to maintain a sharply defined melt zone at higher temperatures. Genuine E3D HeatBreaks feature a refined internal surface finish to reduce extrusion force and improve retraction reliability. Made from grade 5 titanium, these HeatBreaks are exceptionally strong and have lower...

PT100s are high temperature, high-accuracy temperature sensors that you can now use on your E3D-v6 HotEnd instead of a thermistor or thermocouple. PT100s are able to measure higher temperatures than thermistors - up to 400°C and are more accurate than both thermistors and thermocouples in general. The PT100 sensors are also very...

Sleeker, more moddable, and easier to use than ever: we've upgraded the Cyclops and Chimera for usability and stunning results. Get the Chimera+ for two-filament, two-nozzle dual extrusion or the Cyclops+ for two-filament, one-nozzle extrusion. Available as a water- or air-cooled HotEnd, in 12V and 24V. Suitable for 1.75mm bowden setups...

This precision milled POM mounting plate is useful for printers that have 50mm spaced holes below the extruder. Fits tightly around the E3D-v6 HotEnd groove mount and allows you to clamp the HotEnd up to your extruder with 2x screws. Specifications Material: POM (Delrin) Mounting Hole Spacing: 50mm Compatibility: E3D...

Collet clips prevent accidental PTFE releases and allow easy identification of filament diameters. Used on many E3D Bowden HotEnds, including the V6 and Lite6. Specifications Pack size: 2 x Collet Clips Compatible with: E3D Bowden HotEnds (V6, Lite6) Available sizes: 1.75mm and 3mm

Allow your HotEnd to print at higher temperatures with better accuracy and easier assembly with a PT100 sensor. Note: In most cases, an amplifier board will be required, along with a spare 5V, GND, and a signal pin. Specifications Type: PT100 RTD (Resistance Temperature Detector) Compatible with: E3D V6 HotEnd

This is an old-style thermistor clamping heater block for a V6 HotEnd. To upgrade to the newer sensor cartridge-style heater block, check out the V6 block & sock kit. Contents V6 HeaterBlock (old thermistor-clamping style) M3x0.5x4 socket dome screw and washer to clamp thermistor M3x0.5x10 socket dome screw to clamp heater...

These are the same thermistors originally used in E3D's V6 and Lite6 HotEnds — handy if you need a replacement! Note that these have now been replaced on newer HotEnds by thermistor cartridges. Semitec's 104GT2 thermistors feature a higher accuracy than regular thermistors — recommended for temperature-critical printing. In Marlin firmware, these...

A NEMA 17 34N-cm stepper motor with D-shaft and a 100cm long cable. These compact but powerful NEMA 17 stepper motors are great for use with the Titan extruder — particularly if you're after maximum torque for Bowden or Volcano setups. This motor is lighter and shorter than a typical NEMA 17 motor,...

Looking for higher temperature performance? Upgrade your HotEnd with a plated copper V6 heater block, suitable for E3D cartridge-style temperature sensors. A plated copper V6 heater block allows you to reach temperatures exceeding 320°C (providing you use a PT100, PT1000 or thermocouple) unlocking the possibilities of printing high-temperature filaments such as Ultem and...

These are the same 30mm fans that are included with the E3D V6 and Lite6. If you're looking for a replacement, this is the fan that you're after. Specifications Dimensions: 30 x 30 x 10mm Lead Length: 1000mm

We love our RUMBA+ boards! They're great - plenty of stepper drivers, heater/fan channels to spare, and they're built like a tank. Their biggest weakness? Like most other printer control boards, they're 8-bit. Built around the same ATmega2560 that powers RAMPS, there are limits to what they can do and how quickly...