RAMPS 1.4 Printer Control Board
Out of stock!
This is a RepRap Arduino Mega Pololu Shield - commonly known as a RAMPS board. These boards are version 1.4, which is the latest.
These shields attach to an Arduino Mega 2560, and allow the microcontroller to connect to your RepRap's various electrical components - power supply, motors, heaters, fans - and so on.
These boards are version 1.4 - the latest design available, which is very universally compatible with 3D printer electronics. They support up to two extruders (provided you have the stepstick drivers for each), and also have two sets of pins to connect Z-axis motors - meaning designs such as the Prusa Mendel which make use of two Z-motors no longer require any rewiring/splicing - making setup easier and faster.
Specifications:
- PCB Colour: Red
- Version: RAMPS 1.4
- Fully assembled, stepper jumpers supplied
- Product Code: RAMPS-14
- Availability: In Stock
- $24.95
- Ex Tax: $22.68
Thermistor - 100K 1% NTC 3950 - 2 Pack
This is a 100K NTC thermistor, ideal for use with any RepRap / 3D printer. They are suitable for ..
$4.95 Ex Tax: $4.50
12V 40W Ceramic Cartridge Heater
These ceramic heater cartridges are perfect for 3D printer hotends. They heat up much faster than tr..
$5.95 Ex Tax: $5.41
Arduino Mega 2560 R3
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560 (datasheet). It has 54 digi..
$21.95 Ex Tax: $19.95
Stepstick - A4988 RepRap Stepper Motor Driver
These stepper drivers are built around Allegro's A4988 stepper driver IC. This is one of the most co..
$6.95 Ex Tax: $6.32
50mm 5V Blower Fan
This centrifugal fan (also known as a blower or squirrel cage fan) pushes a large amount of air in a..
$7.65 Ex Tax: $6.95
Stepper Motor Connector Kit
Stepper motors come with bare wires? No fear - this kit is here to help! Featuring five four-pin ..
$4.95 Ex Tax: $4.50
LCD Controller + SD Card Reader for RAMPS
The Smart Controller is a graphical user interface to control your 3D printer without the need for a..
$24.95 Ex Tax: $22.68
12V 30A 360W Power Supply
Looking for a power supply that has enough juice to run your 3D printer? Look no further! The pow..
$49.95 Ex Tax: $45.41
50mm 12V Blower Fan
This centrifugal fan (also known as a blower or squirrel cage fan) pushes a large amount of air in a..
$9.85 Ex Tax: $8.95
TinyFan - RAMPS Fan Expansion Board
TinyFan is a handy little board that attaches to RAMPS, and allows you to control an extra two fans...
$16.95 Ex Tax: $15.41
MightyFan - RAMPS Fan Expansion Board
MightyFan is TinyFan's bigger brother. It does the same job - it lets you add extra controlled fans ..
$26.95 Ex Tax: $24.50
Mark2 Power Wiring Kit
We had a bunch of custom wiring harnesses made up to make our Mark2 3D Printers easier and tidier to..
$27.45 Ex Tax: $24.95
12V 20A 250W Power Supply
Looking for a power supply that has enough juice to run your 3D printer? Look no further! The pow..
$39.95 Ex Tax: $36.32
RUMBA+ Control Board
Note: We are now shipping the new and improved v1.4 RUMBA+ boards! We have a detailed blog-..
$149.95 Ex Tax: $136.32
I2C Splitter Board
This is a handy little board that takes one four-pin input and shares it between six outputs. T..
$9.95 Ex Tax: $9.05
Stepstick - DRV8825 RepRap Stepper Motor Driver
These stepper drivers are built around TI's DRV8825 stepper driver IC. The DRV8825 supports higher c..
$7.95 Ex Tax: $7.23
Graphic LCD Controller + SD Card Reader for RAMPS
The Graphic LCD Controller is a graphical user interface to control your 3D printer without the need..
$34.95 Ex Tax: $31.77